Standing Seam Panels by Western Slope Metals

Standing seam panels roll-formed by Western Slope Metals, usually right on your job site. We run three standing seam systems. They differ in how each panel is held to the roof: clips with a snap-lock seam, clips with a mechanically seamed lock, or a screwed nail flange.

Speckled Galvanized Rust mechanically seamed standing seam metal roof with a stone chimney near McClure Pass, Colorado
Mechanically seamed Speckled Galvanized Rust standing seam roof near McClure Pass, Colorado.

See every color and finish we offer. Enter your email and we’ll send the full catalog PDF right away.

Get Our Free Color Catalog

7 + 4 =

Compare Our Standing Seam Systems

System Profile Seam How it attaches Availability
Snap-lock with clips SS450SL 1½ in Clips under the seam; panels snap together In house
Mechanical seam SS150 1½ in Clips under the seam; seams closed with a power seamer In house
Mechanical seam, 2-inch SSQ200 2 in Clips under the seam; seams closed with a power seamer Upon request; schedule in advance
Nail-flange snap-lock FF100 1 in Screwed through a slotted flange; no clips Upon request; schedule in advance

Snap-Lock with Clips (SS450SL)

Our standard snap-lock panel is the SS450SL, with a 1½-inch seam. Concealed clips are screwed to the roof deck under each seam, and the next panel snaps over the leg. No seaming tool is needed.

Because the clips hold the panel instead of screws through the panel, the panels can move with temperature changes. Once panels run longer than 25 feet, we use two-piece expansion clips to allow for that movement. Snap-lock is a common choice for homes, garages and shops.

Seam height
1½ inches
Panel width
Usually 16 or 20 inches
Gauge
24 or 26 gauge steel
Fastening
Concealed clips
Panels over 25 feet
Two-piece expansion clips
Availability
In house
SS450SL 1.5 inch snap-lock standing seam panel and snapped seam rendering
SS450SL 1½-inch snap-lock panel and closed seam. Drawing: New Tech Machinery.
SS450SL 1.5 inch snap-lock standing seam panel profile drawing with dimensions
SS450SL 1½-inch snap-lock profile. Drawing: New Tech Machinery.

SS450SL snap-lock spec sheet (PDF)

Mechanical Seam (SS150 and SSQ200)

Our SS150 mechanical seam panel also has a 1½-inch seam and is held down with concealed clips. After the panels are set, a power seamer runs up each seam and folds it closed.

Mechanically seamed roofs are normally 24 gauge. For a taller seam, the SSQ200 2-inch mechanical seam profile is available upon request. Please schedule it in advance.

Seaming tool clamped on the seam of a Speckled Galvanized Rust standing seam metal roof panel near McClure Pass, Colorado
Seaming tool on a Speckled Galvanized Rust standing seam panel near McClure Pass, Colorado.
Seam height
1½ inches (SS150) or 2 inches (SSQ200)
Panel width
SS150 usually 16 or 20 inches; SSQ200 normally 18 inches
Gauge
Normally 24 gauge steel
Fastening
Concealed clips; seams mechanically closed
Panels over 25 feet
Two-piece expansion clips
Availability
SS150 in house; SSQ200 upon request, schedule in advance
SS150 1.5 inch mechanical seam standing seam panel profile drawing with dimensions
SS150 1½-inch mechanical seam profile. Drawing: New Tech Machinery.
SSQ200 2 inch mechanical seam standing seam panel profile drawing with dimensions
SSQ200 2-inch mechanical seam profile. Drawing: New Tech Machinery.

SS150 mechanical seam spec sheet (PDF) · SSQ200 2-inch mechanical seam spec sheet (PDF)

Nail-Flange Snap-Lock (FF100)

The FF100 nail-flange panel has a 1-inch snap-lock seam with no clips. A flange along one edge is screwed to the roof deck through pre-punched slots, and the next panel snaps over it to cover the screws.

Because the flange is screwed down, nail-flange panels should never be longer than 25 feet. For roof runs longer than 25 feet, we recommend our SS450SL snap-lock or SS150 mechanical seam panels.

The FF100 profile is available upon request. Please schedule it in advance.

Seam height
1 inch
Gauge
24 or 26 gauge steel
Fastening
Screws through a slotted flange; no clips
Maximum panel length
25 feet
Availability
Upon request; schedule in advance
FF100 1 inch nail flange snap-lock standing seam panel profile drawing with slotted fastening flange
FF100 1-inch nail-flange snap-lock profile with slotted fastening flange. Drawing: New Tech Machinery.

FF100 nail-flange spec sheet (PDF)

About these drawings: the profile drawings and spec sheets are New Tech Machinery documents for the roll-forming tooling. Coverage widths shown are the full range the tooling can produce. Most of our 1½-inch snap-lock and mechanical seam projects use 16- or 20-inch panels, and our 2-inch mechanical seam panels are normally 18 inches. Panel width, gauge, length and finish are confirmed on your quote.

Colors and Trim

Panels are available in Western States colors, including matte, wood-grain, rusted and zinc finishes, plus real copper and copper-painted steel. We bend matching trim and flashing for every job.

View Color Chart · Try the Color Visualizer

See our metal roofing page for installation, snow retention and heat cable, or our cold roof system for heavy-snow homes. Contractors can order panels roll-formed on site through our roofing partners program.

Request a Standing Seam Quote

Send your roof measurements or plans, the system you want, gauge and color, and whether you need material only or installation.

Call (970) 975-0612 to discuss your project or schedule a visit. Shop visits are by appointment only at 1454 Hwy 50, Delta, CO 81416.

Request a Quote Call (970) 975-0612